IR@NITK: Browsing DSpace

Browsing by Author Herbert, M.A.

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:

Showing results 1 to 20 of 21 next >

Issue Date	Title	Author(s)	Supervisor(s)
2019	Active Upper Arm Exoskeleton - Design and Kinematic Analysis	Santra, P.; Mukhopadhyay, A.; Debnath, B.; Herbert, M.A.; Bhaumik, S.	-
2019	Assessment of influence of process parameters on properties of friction stir welded Al-Ce-Si-Mg aluminium alloy	D'Souza, A.D.; Rao, S.S.; Herbert, M.A.	-
2014	Correlation of Tribological Properties with Microstructure and Mechanical Properties of Graphite Cast Irons Centrifugally Cast for Engine Liner	Desai, Gowda, H.S.; Mukunda, P.G.; Herbert, M.A.	-
2018	Development of novel cutting tool with a micro-hole pattern on PCD insert in machining of titanium alloy	Rao, C.M.; Rao, S.S.; Herbert, M.A.	-
2013	Effect of centrifugal and gravity casting technique over metallographic and mechanical properties of spheroidal graphite iron	Desai, Gowda, H.S.; Mukunda, P.G.; Herbert, M.A.	-
2019	Effect of low temperature annealing on the properties of nano Ni-Ti alloys	Mukunda, S.; Vinyas, M.; Narendranath, S.; Herbert, M.A.	-
2016	Effect of low temperature annealing on the wear properties of NITINOL	Mukunda, S.; Naths, N.; Herbert, M.A.; Mukunda, P.G.	-
2011	Effect of mushy state rolling on age-hardening and tensile behavior of Al-4.5Cu alloy and in situ Al-4.5Cu-5TiB2 composite	Siddhalingeshwar, I.G.; Herbert, M.A.; Chakraborty, M.; Mitra, R.	-
2019	An Efficient Approach to Optimize Wear Behavior of Cryogenic Milling Process of SS316 Using Regression Analysis and Particle Swarm Techniques	Karthik, Rao, M.C.; Malghan, R.L.; ArunKumar, S.; Rao, S.S.; Herbert, M.A.	-
2020	An Experimental and Numerical Approach to Study the Performance of Modified Perforated Cutting Tools on Machining of Ti 6Al 4V Alloy	Rao, C.M.; Rao, S.S.; Herbert, M.A.	-
2017	Experimental study on linear displacement measurement sensor using RGB color variation technique with PID controller	Murthy, A.; Rao, S.S.; Herbert, M.A.; Navin, Karanth, P.	-
2018	Influence of modified cutting inserts in machining of Ti-6Al-4V alloy using PCD insert	Rao, C.M.; Rao, S.S.; Herbert, M.A.	-
2019	Investigation of errors in microcontroller interface circuit for mutual inductance sensor	Anarghya, A.; Rao, S.S.; Herbert, M.A.; Navin, Karanth, P.; Rao, N.	-
2016	Investigation on microstructure and mechanical properties of Friction Stir Welded AA6061-4.5Cu-10SiC composite	Herbert, M.A.; Shettigar, A.K.; Nigalye, A.V.; Rao, S.S.	-
2018	Machining Parameters Optimization of AA6061 Using Response Surface Methodology and Particle Swarm Optimization	Lmalghan, R.; Rao, K.; ArunKumar, S.; Rao, S.S.; Herbert, M.A.	-
2014	Microstructure and hardness of friction stir welded aluminium-copper matrix-based composite reinforced with 10 wt-% SiCp	Kumar, A.; Veeresh, Nayak, C.; Herbert, M.A.; Rao, S.S.	-
2019	Microstructure evolution and mechanical properties of friction stir welded AA6061/rutile composite	Prabhu, S.R.B.; Shettigar, A.K.; Herbert, M.A.; Rao, S.S.	-
2013	Preparation and evaluation of mechanical properties of Al-6061 reinforced with graphite and fly ash of seed husk (Honge) particulate metal matrix composite	Edrard, C.; Kapilan, N.; Herbert, M.A.	-
2016	Soft computing techniques during drilling of bi-directional carbon fiber reinforced composite	Shetty, N.; Herbert, M.A.; Shetty, R.; Shetty, D.S.; Vijay, G.S.	-
2019	Studies on the Effect of Process Parameters in Turning of Ti-6Al-4V Alloy Using Topsis	Rao, C.M.; Rao, S.S.; Herbert, M.A.	-

Showing results 1 to 20 of 21 next >