IR@NITK: Browsing DSpace

Browsing by Author Rao, S.S.

Jump to: 0-9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
or enter first few letters:

Showing results 1 to 20 of 45 next >

Issue Date	Title	Author(s)	Supervisor(s)
2014	Analysis of surface roughness and hardness in ball burnishing of titanium alloy	Revankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N.	-
2014	Analysis of surface roughness and hardness in titanium alloy machining with polycrystalline diamond tool under different lubricating modes	Revankar, G.D.; Shetty, R.; Rao, S.S.; Gaitonde, V.N.	-
2017	Application of particle swarm optimization and response surface methodology for machining parameters optimization of aluminium matrix composites in milling operation	Malghan, R.L.; Rao, K.M.C.; Shettigar, A.K.; Rao, S.S.; D Souza, R.J.	-
2019	Assessment of influence of process parameters on properties of friction stir welded Al-Ce-Si-Mg aluminium alloy	D'Souza, A.D.; Rao, S.S.; Herbert, M.A.	-
2011	Behavioral study of alumina nanoparticles in pool boiling heat transfer on a vertical surface	Hegde, R.N.; Reddy, R.P.; Rao, S.S.	-
2012	Boiling induced nanoparticle coating and its effect on pool boiling heat transfer on a vertical cylindrical surface using CuO nanofluids	Hegde, R.N.; Rao, S.S.; Reddy, R.P.	-
2010	Critical heat flux enhancement in pool boiling using alumina nanofluids	Hegde, R.; Rao, S.S.; Reddy, R.P.	-
2009	Determination of transient and steady state cutting in face milling operation using recurrence quantification analysis	Mhalsekar, S.D.; Mohan, G.; Rao, S.S.; Gangadharan, K.V.	-
2010	Development of a surface roughness prediction system for machining of hot chromium steel (AISI H11) based on artificial neural network	Rai, R.; Kumar, A.; Rao, S.S.; Shriram	-
2018	Development of novel cutting tool with a micro-hole pattern on PCD insert in machining of titanium alloy	Rao, C.M.; Rao, S.S.; Herbert, M.A.	-
2014	Direct torque controlled induction motor drive based on cascaded three two-level inverters	Kumar, T.V.; Rao, S.S.	-
2018	Effect of process parameters in face milling operation and analysis of cutting force using indirect method	malghan, R.L.; Rao, K.M.C.; ArunKumar, S.; Rao, S.S.; D Souza, R.J.	-
2015	Effect of Rotational Speeds on the Cast Tube During Vertical Centrifugal Casting Process on Appearance, Microstructure, and Hardness Behavior for Al-2Si Alloy	Shailesh, Rao, A.; Tattimani, M.S.; Rao, S.S.	-
2019	An Efficient Approach to Optimize Wear Behavior of Cryogenic Milling Process of SS316 Using Regression Analysis and Particle Swarm Techniques	Karthik, Rao, M.C.; Malghan, R.L.; ArunKumar, S.; Rao, S.S.; Herbert, M.A.	-
2020	An Experimental and Numerical Approach to Study the Performance of Modified Perforated Cutting Tools on Machining of Ti 6Al 4V Alloy	Rao, C.M.; Rao, S.S.; Herbert, M.A.	-
2012	Experimental studies on CHF enhancement in pool boiling with CuO-water nanofluid	Hegde, R.N.; Rao, S.S.; Reddy, R.P.	-
2009	Experimental studies on turning of discontinuously reinforced aluminium composites under dry, oil water emulsion and steam lubricated conditions using TAGUCHI's technique	Shetty, R.; Pai, R.; Rao, S.S.	-
2011	Experimental study on CuO nanoparticles in distilled water and its effect on heat transfer on a vertical surface	Hegde, R.N.; Rao, S.S.; Reddy, R.P.	-
2017	Experimental study on linear displacement measurement sensor using RGB color variation technique with PID controller	Murthy, A.; Rao, S.S.; Herbert, M.A.; Navin, Karanth, P.	-
2012	Flow visualization and study of critical heat flux enhancement in pool boiling with Al 2O 3-water nanofluids	Hegde, N.R.; Rao, S.S.; Reddy, R.	-

Showing results 1 to 20 of 45 next >